Complete Stock Moto Package
|
| Selected Ad |
| Category: |
Shifter Karts |
| Title: |
Complete Stock Moto Package |
| Ad
Number: |
3438 |
| Date Posted: |
4/5/2012 |
| Contact: |
Mark Heinert
Oak Creek, WI
|
|
|
|
|
|
Description
2008 PTK Chassis with Stock Cr125
-3 race weekends since completely freshened
-Shockwave “free heel” engine mount
-Champion Radiator with silicone hoses
-Mychron 3 gold
-Hegar pipe and airbox mounts
-RLV R4 Pipe and M4 12” Silencer
-Custom Coil holder
-PWM pump around carb with Mikuni dual pumps
-RLV 3 hole airbox and K&N air filter
-Streeter Big Foot kart stand
-Streeter vertical kart stand
-Practically new spare set of Douglas magnesium rims with original used YHCs
-Engine Gears 14, 15 (2), 16 (2), 17 (2), 19, 21
-Rear Gears 21, 24, 25, 26, 27, 23
-5 spare 428 DID Chains
-Pilot Jets 60 (1), 55 (2), 45 (1), 50 (3), 58 (2), 48 (1)
-Main Jets 190 (4), 195 (1), 180 (4), 182 (2), 185 (2), 170 (2), 172 (1), 175 (2), 178 (3), 155 (1), 158 (2), 160 (1), 162 (2), 165 (2), 168 (3)
-Needles DGJ, CCJ (2), CGK (2), DGH
-4 needle “c” clips, 2 cable stretchers, Keihin Screws, Float bowl nut, throttle spring collar
-Throttle cables (3), Throttle cable with hosing (1), clutch cable (1), clutch cable with housing (1), cable housing, 90 degree radiator hoses (2)
-Misc plug wire, CR125 coil, Mikuni pump around spare pump diaphrams, Keihin carb vent hoses, grounding wire, reed cage gaskets (3), Carbontech reeds (2), fuel line, fuel filters (3), NGK plug boot
-Exhaust header “O” rings (12), Keihin #6 slide for carb, Front wheel “C” clip, throttle cable clamp, valve stems (2), front spindle spacers (4), 428 chain master links (6), motor mount chassis blocks, Mychron wheel magnets, self-adhesive wheel weights, misc CR125 “0” rings and washers, exhaust springs (7), 1/4” hose barb, king pin bushings (2), fuel tank knob, brake rod clips (4), old style transponder holder; exhaust mount, and several other parts
-1/4 Redline lightweight shockproof gear oil, ¼ PJ1 Clutch oil, 5 full Burris HI Rev Caster Oil, 2 seat post struts, rear hub, front hub, J arm, push bolt for engine tightener, spare bolts for shockwave mount (3), New 6003Z front spindle bearings (5), New 6082C3 bearing for steering shaft (2), number plate mounting brackets (2), Coil mount, 4 hole Righetti Ridolfi Airbox
-Tire changer, 50mm Axle, electric frying pan for boiling chain
-Spares – Brand New complete set of factory graphics, Large PTK fuel tank, 2 new 280mm tie rods, Left spindle, new brake, and throttle pedal, New Ven 4 brake pads (4), steering hub, rear chassis bar, 2 heel blocks, rear bumper, rear lower bumper bar, Champion radiator mounts
$5,800 - Open to Offers
www.flickr.com/photos/58945705@N04/sets/72157628906239507 |
|
|
|
|